Skip to content
SLAG CLEANER TW1500 — Slag Removal Machine for Slats up to 10 mm
LUCOHE Portable

TW1500

SLAG CLEANER TW1500 — Slag Removal Machine for Slats up to 10 mm

Portable LUCOHE SLAG CLEANER TW1500 slag removal machine for cutting tables with thicker slats: slats 3 to 10 mm thick with at least 47 mm pitch, on laser tables up to 20 kW, plasma and oxy-fuel tables. 1,500 W motor on 380 V three-phase, 1,300 strokes per minute, replaceable tungsten carbide blade and one-piece die-cast aluminium body. On wheels and guided by one operator from a long handle; 41 kg net. For slats 3–5 mm thick with at least 40 mm pitch, see the SLAG CLEANER TW2300. Quote only.

380 V three-phase
1,500 W
380 V three-phase
Slat thickness
3–10 mm
Slat thickness
Slat pitch
≥ 47 mm
Slat pitch
Laser table
≤ 20 kW
Laser table
Price on request

Industrial equipment or spare part available by quotation. We verify configuration, technical compatibility, lead time and shipping before confirming the final price.

Quick quotation

Leave your details and we will review configuration, accessories, installation and transport before confirming price.

Technical sheet

Technical data

Model TW1500
Rated power 1,500 W
Power supply 380 V three-phase, 50 Hz · supply within +5 % of the rated voltage
Suitable for Laser cutting tables up to 20 kW, plasma and oxy-fuel tables
Slat thickness 3–10 mm
Minimum slat pitch 47 mm
Slag cleaning width 40–100 mm according to the manufacturer's table; keeping the slag under 25 mm wide is recommended
Blade frequency 1,300 strokes per minute
Continuous operation 1 hour, then 10–20 minutes of rest
Cleaning tool Tungsten carbide blade, replaceable
Body One-piece die-cast aluminium alloy
Operation One operator, from a long handle beside the table · removable wheel assembly
Dimensions 85 × 45 × 55 cm
Net weight 41 kg

How it is used

  1. 1 Remove the wheel assembly and set the machine flat on the table, with the blade head in the gap between two slats and the switch off.
  2. 2 Lift the handle slightly, switch on and lower the head onto the slat: the weight of the machine rests on the table and cleaning starts.
  3. 3 Push gently along the slat, parallel to it, without swinging it sideways. The machine advances by itself as it removes the slag; it needs guiding, not forcing.
  4. 4 At a crossbeam, lift or lower the handle so the head clears it, then carry on. At the end of the slat, lift the head, swing to the next slat and lower it again.
  5. 5 To stop, lift the handle so the head comes off the slat and switch off.

For the longest life

Clean regularly, before the slag on the slat grows beyond 25 mm wide. Keep to the duty cycle: no more than one hour of continuous work, then 10–20 minutes of rest. Do not force the machine forward or pull it backwards to clear thick slag: that is what wears the blade and the motor.

Wear parts and maintenance

Part When Notes
Tungsten carbide blade When cleaning performance drops Normal wear part. Its life depends on how thick the slag is and how often the table is cleaned: a table cleaned often, with thin slag, wears the blade far less.
Extension spring When it breaks One spare spring supplied with the machine.
Grease, top of the machine Every 20 hours of work Not needed before first use.
Grease, blade arm pivot Every 20 hours of work At the joint between the blade and the arm.
Mounting screws Check frequently Retighten any loose screw at once.

Replacement blades and springs are supplied by Herramentalia.

Request Quote

Get in touch for quotes, technical support or any enquiry