Skip to content
SLAG CLEANER TW2300 — Industrial Slag Removal Machine
LUCOHE Portable

TW2300

SLAG CLEANER TW2300 — Industrial Slag Removal Machine

Portable 2,300 W LUCOHE SLAG CLEANER TW2300 for removing bonded slag and dross on laser, plasma and oxy-fuel cutting table slats. It runs along each slat and removes the slag with a replaceable tungsten carbide blade, without bending or damaging the slat. For flat and toothed slats 3–5 mm thick with at least 40 mm pitch, on laser tables up to 15 kW. 220 V single-phase, working speed 5–8 m/min, on wheels and handled by one operator. For slats over 5 mm thick, see the SLAG CLEANER TW1500. Quote only.

220 V single-phase
2,300 W
220 V single-phase
Slat thickness
3–5 mm
Slat thickness
Slat pitch
≥ 40 mm
Slat pitch
Laser table
≤ 15 kW
Laser table
Price on request

Industrial equipment or spare part available by quotation. We verify configuration, technical compatibility, lead time and shipping before confirming the final price.

Quick quotation

Leave your details and we will review configuration, accessories, installation and transport before confirming price.

Technical sheet

Technical data

Model TW2300
Rated power 2,300 W
Power supply 220 V single-phase, 50 Hz · supply within +5 % of the rated voltage
Suitable for Laser cutting tables up to 15 kW, plasma and oxy-fuel tables
Slat thickness 3–5 mm, flat or toothed
Minimum slat pitch 40 mm
Maximum slag width on the slat 25 mm
Working speed 5–8 m/min along the slat
Duty cycle Up to 1 hour of continuous work, then 10–20 minutes of rest
Cleaning tool Tungsten carbide blade, replaceable
Base plate Stainless steel, with clip-on wheel assembly
Operation One operator, from a long handle beside the table
Machine dimensions 56 × 25 × 32 cm
Packed dimensions / weight 84 × 32 × 51 cm · 36 kg

How it is used

  1. 1 Remove the wheel assembly and set the machine flat on the table, with the blade head in the gap between two slats and the switch off.
  2. 2 Lift the handle slightly, switch on and lower the head onto the slat: the weight of the machine rests on the table and cleaning starts.
  3. 3 Push gently along the slat, parallel to it, without swinging it sideways. The machine advances by itself as it removes the slag; it needs guiding, not forcing.
  4. 4 At a crossbeam, lift or lower the handle so the head clears it, then carry on. At the end of the slat, lift the head, swing to the next slat and lower it again.
  5. 5 To stop, lift the handle so the head comes off the slat and switch off.

For the longest life

Clean regularly, before the slag on the slat grows beyond 25 mm wide. Keep to the duty cycle: no more than one hour of continuous work, then 10–20 minutes of rest. Do not force the machine forward or pull it backwards to clear thick slag: that is what wears the blade and the motor.

Wear parts and maintenance

Part When Notes
Tungsten carbide blade When cleaning performance drops Normal wear part. Its life depends on how thick the slag is and how often the table is cleaned: a table cleaned often, with thin slag, wears the blade far less.
Carbon brushes (2) Inspect regularly; replace both when worn down to 6 mm Keep them clean and free to slide in their holders.
Extension spring When it breaks One spare spring supplied with the machine.
Grease, top of the machine Every 20 hours of work Not needed before first use.
Grease, blade arm pivot Every 20 hours of work At the joint between the blade and the arm.
Mounting screws Check frequently Retighten any loose screw at once.

Replacement blades, carbon brushes and springs are supplied by Herramentalia.

Request Quote

Get in touch for quotes, technical support or any enquiry